Janesville Tool & Manufacturing, Inc.
HomeProductsCatalog RequestsContact UsAbout UsSiteMap

Pneumatic Press Attachments

T-10AP and T-10BP External Timer Operation

magnetic timer kitsThe T-10AP & T-10BP replaces the Magnetic Timer Switch and allows the user much more accurate down position reading then the previous magnetic switch.

This system allows the operator to delay the down stroke by .1 second up to 999 hours.

Advantages Include:

  • Assurance that the press makes full stroke.
  • Allows operator to remove hands from palm buttons to do other operations.
  • Assures cylinder gets to force complete.

1) Both "buttons" are actuated within one half second of each other and the cylinder advances toward the switch. If one or both "buttons" are released before cylinder completes its stroke it will return.

2) A prewired prox switch is located on the stop plate to inform the press that the cylinder is forward. This turns on the amber light and begins the timing sequence. Once the amber light is lit the operator may remove his/her hands from the "buttons" or leave them on and the press will stay down until the timer completes its delay.

3) When the timer completes its delay (.1 second to 999 hours), a red light is lit. If the operator lifts his/her hands on the "buttons", the cylinder will return. If the operator removes their hands, both "buttons" will (at the same time) need to be reactivated to return the cylinder.

4) The press is ready for the next cycle once both "buttons" have been released.

To Adjust Timer:

1) Use the (A) mode, on the left side of timer.

2) Set right side of timer for time units.

3) To change the time delay setting:

To make the numbers in lower display smaller push the selector button over the digit you wish to reduce. To make larger numbers push the selector button under the digit you wish to increase.

T-10AP
T-10BP


Adjustable Down Stop-Anti Rotate Mechanism

Anti Rotate MechanismThe Adjustable Down Stop-Anti Rotate Mechanism makes use of a double-ended cylinder and tooling to provide an adjustable end stop to the cylinder travel. In addition, the cylinder rod is prevented from rotating. Shown with guard removed for clarity.



Model 523 Quick Exhaust Valve

Tool Adaptor

Allows exhaust air to be exhausted at the cylinder rather than the solenoid valve to speed up press cycle.



Model 512 & Model 544 Filter/Regulators

Model 512 & Model 544 Filter/RegulatorsRecommended for use on all pneumatic presses to remove moisture and to allow the user accurate supply pressure.

Model 512 - used for A-500 series thru A-3000 series presses, comes standard with a 1/4" N.P.T. pipe fitting.

Model 544 - used for A-4000 & A-5000 series presses, comes standard with a 1/2" N.P.T. pipe fitting.



Model 750 220 v Transformer Kit

Transformer KitModel 750 220 v Transformer Kit 240 v to 120 v-50/60 Hz



Air/Oil

Air/Oil Systems can reduce break through serge as well as provide the smoothness and rigidity of a hydraulic system without the inherent high costs and space consuming components needed to operate the press. (Add suffix A/O to the end of the model # when ordering.)



The Tool Adapter

The Tool Adapter is designed for easy assembly and disassembly of JT & M's mini die sets. The tool adapter threads into the ram of the cylinder with either a 1/2-13 thread for 1 3/4" and the 3" bore or a 3/4-10 thread for the 4 1/2" bore and multi-stage cylinder. Choice of lengths include 1 1/2", 2 1/2", 3 1/2" or 4 1/2". This accessory is identified by TAl/2 - length for 1/2-13 thread or TA3/4 - length for 3/4-10 thread.

Example:

TA1/2 - 4 1/2" (1/2 - 13 thread by 4 1/2" lg.)

The Tool Adapter



Air Press Guarding G-0123

This new cost effective guarding protects three sides of the pneumatic press from co-workers reaching into the press during operation. This guard is available for the A-500, A-1000, A-2000, and A-3000 pneumatic series presses.

When installed the G-0123 guarding sits directly on the control box and does not take up additional table space. This guard can be installed on new and existing presses and comes standard with all brackets to mount via the four bottom cover screws; no new machining is required.

Guarding Size:

G-0123 (18 3/16" x 20" x 16")


Air Press Guarding G-01235

Cost-effective guarding is available for the A-500, A-1000, A-2000, A-3000, and A-5000 series pneumatic presses. The rigidity of the wire mesh, aluminum inter-locking frame, and quality construction will prevent any intrusion during press operation.

Guarding Size:

G-01235 (29 1/2" x 33 1/2" x 24 3/4")


*Product specifications and pricing subject to change without notice.